Corvette Z06 Forum banner

CAGS ... Which Connector?

Jump to Latest Follow
1 - 5 of 5 Posts
proexpert

·
Registered
Joined
·
6,273 Posts
Discussion Starter · #1 ·
OK, I have the resistor, and am under the car. There are conflicting posts about which connector is the CAGS. There are three connectors that I can see. One is on the passenger side (I call that the right side of the car) and two are on the drivers side. One tutorial says it is the forward most connector, which is on the right side. Another tutorial says it is on the left side, but does not mention which one. I have looked at all the pictures, sorry I'm still not sure. Can someone who has done this please tell me which connector it is? Thanks in advance.

BTW, put in the B&M ripper shifter yesterday, awesome! /phpBB/images/smiles/icon_smile.gif
 
D

·
Registered
Joined
·
528 Posts
#3 ·
Just had mine done couple days ago, works great. Driver side, top gray/blue connector. Just make sure you seal the connector up well.

Good luck.
 
Save Share
Reply
G

·
Registered
Joined
·
41 Posts
#4 ·
I did mine yesterday. Left side, upper grey connector. The job took about 4-5 minutes. Works great!
 
1 - 5 of 5 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Recommended Reading
Read More
  1. C5 Z06 - Pit Road
    Im about to install my third set of rings in this build. The engine is a stout 441 cube LSX 454 block. 4" stroke GM LS7 Crank, 4.185" bore. Eagle 6.125" Rods. Street raced occasionally in Mexico. Driven almost daily prob 200 to 300 miles a week. Using 1QT or more a week. It almost uses as...
  2. C5 Z06 - Pit Road
    Gonna be buying a Z06 real soon and wondering how much HP the stock rods/pistons (bottom end etc.) can take as far as power production. I'm gonna porbably do Ported heads/Mti cams/full exhaust and some other junk but need a good base on how far is too far for the stock motor? I tried to a do...
  3. C5 Z06 - Pit Road
    Been thinking about a few additional modifications to my car. I currently have a 2002 Lingenfelter C5 Z06 with the Magnuson supercharger package, cold air intake, and B&B exhaust. I believe the car dyno'ed at 492 rwhp pushing 6 psi of boost from Lingenfelter. I have been debating lately on the...
  5. C5 Z06 - Pit Road
    Hey all- In the middle of my intercooled magnacharger install (just finished putting the front end back together after drilling into the harmonizer, etc) and am starting to replace the fuel pump.... heres the problem - need to have the tank at 1/8th or less and I am nearly full. I cannot get...
  6. C5 Z06 - Pit Road
    Hello ! I just bought a 04 z06 with a brand new built ls3 and 6 speed transmission and rear end. After driving it for a bit I noticed a sort of faint spinning grinding noise which seems to be coming somewhere under the shifter . It’s there when idling and when foot is on the clutch . It’s not...
Read More
About this Discussion
4 Replies
4 Participants
Last post:
proexpert
Corvette Z06 Forum
We’re a forum community dedicated to the Chevy Z06 Corvette. Come check out discussions on performance, specifications, modifications, purchasing, maintenance and more!
Full Forum Listing
Explore Our Forums
C5 Z06 - Grandstand C5 Z06 - Pit Road Member Sales/Trades - Parts & Cars C6 Z06 - Pit Road C6 Z06 - Grandstand
Recommended Communities
Community avatar for Chevrolet Corvette Forums
Chevrolet Corvette Forums
126K+ members
Community avatar for Snowmobile World
Snowmobile World
214K+ members
Community avatar for Harley Davidson Pan America Forum
Harley Davidson Pan America Forum
NEW!
190+ members
Top